U-Boot 1.1.4 (Jan 8 2007 - 11:12:14) Tektronix, Inc. V1.06 CPU: AMCC PowerPC 440EP Rev. C at 333.333 MHz (PLB=133, OPB=66, EBC=66 MHz) I2C boot EEPROM enabled Internal PCI arbiter enabled, PCI async ext clock used 32 kB I-Cache 32 kB D-Cache Board: Tektronix Route66 IBM 440EP Main Board VCO: 666 MHz CPU: 333 MHz PLB: 133 MHz OPB: 66 MHz EPB: 66 MHz I2C: ready DRAM: 128 MB FLASH: 64.5 MB PCI: Bus Dev VenId DevId Class Int 00 13 10b5 9056 0680 18 00 15 1002 4c59 0300 17 DISP: Type 1 In: serial Out: serial Err: serial Enter password - autobooting in 3 seconds ## Booting image at f0000000 ... Image Name: Linux-2.4.20_mvl31-440ep_eval Image Type: PowerPC Linux Multi-File Image (gzip compressed) Data Size: 1441010 Bytes = 1.4 MB Load Address: 00000000 Entry Point: 00000000 Contents: Image 0: 1033953 Bytes = 1009.7 kB Image 1: 407042 Bytes = 397.5 kB Verifying Checksum ... OK Uncompressing Multi-File Image ... OK cmdline is console=ttyS0,9600 quiet bigphysarea=519 panic=2 root=/dev/mtdblock7 rw mem=131072k Loading Ramdisk to 07f2b000, end 07f8e602 ... OK Checking for firmware update... No USB mass storage devices found to update from. Linux 2.4.20_mvl31-440ep_eval V 1.15 Tektronix Route66 Tue Jun 22 15:19:50 PDT 2010 stat of /var/log/dmesg failed: No such file or directory Warning: loading NiDKEng-1.6 will taint the kernel: non-GPL license - Proprietary See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading NiDUsb-1.6 will taint the kernel: non-GPL license - Proprietary See http://www.tux.org/lkml/#export-tainted for information about tainted modules Warning: loading tek will taint the kernel: non-GPL license - Proprietary See http://www.tux.org/lkml/#export-tainted for information about tainted modules Scope application starting (normal mode) ---------------------- startScopeApp() running Init code ---------------------- versionBuildFWVersionString(): TimestampString: 25-Apr-12 11:13 VersionFIRMWAREVERSIONversion: v2.68 Major ver num: 2 Minor ver num: 68 Initializing Mia[0] Adg523 detected, patching reg offsets Initializing Tek0005[0] Initializing Ibm440[0] Initializing HFD204ADC[1] Initializing HFD204ADC[0] Model id: 0x03 Initializing Ltc1658Dac[0] Board id: 0x01 Initializing M859[3] Initializing M859[2] Initializing M859[1] Initializing M859[0] HFD144[0] ID_REG = 0x00001440 HFD144[1] ID_REG = 0x00001440 HFD144[2] ID_REG = 0x00001440 HFD144[3] ID_REG = 0x00001440 Initializing Hfd144[0] Initializing Hfd144[1] Initializing Hfd144[2] Initializing Hfd144[3] Open Max5362 successful. Initializing Max5362[0] Initializing Ltc1661Dac[1] Initializing Ltc1661Dac[0] Init ADT7468 and locking. Factory Checksum: Stored: 50431, Calculated: 50431 - OK Spc CheckSum: stored: 46504 calculated: 46504 - OK Demux initialization Dram calibration Dram calibration complete Dram Calibration results: ------------------------- DramCal has PASSED on all Demuxs Demux initialization complete Starting POST diags Diag Failure: Mode 100 8, U271,U370-B, 0x00000000 0x00000003 0x00000003 Diag Failure: Mode 100 8, U271,U370-B, 0x00000000 0x00000003 0x00000003 Diag Failure: Mode 100 8, U271,U370-B, 0x00000000 0x00000003 0x00000003 Diag Failure: Mode 100 8, U271,U370-B, 0x00000000 0x00000003 0x00000003 Finished POST diags ---------------------- startScopeApp() running Start code --------------------- ---------------------- startScopeApp() running Run code ----------------------- SIOCSIFFLAGS: Link has been severed OK to connect by: telnet DPO4104-04SKBP 1072 SocketServerService: Socket server daemon started on port 4000. Protocol: Raw ----------------------------------------------------------------- startScopeApp() complete; duration = 27.873596 seconds ================================================================= PID to Task info written to /tmp/threads.txt Power Up Completed at 15:40:10 Enter 'ctrl-\' to quit scopeApp